Broadband Pro consists of a central unit, with a 220V adapter and four speakers. (The speakers are connected to the central unit by cables, the length of each cable is about 20 m.)  Open the top of the central unit by sliding out the two green bolts carefully. Before operation connect the four speakers and the adapter to their place by lifting up the plate at the bottom of the central unit, remove the rubber ring and interlace the cables of speakers and the adapter through this hole. Then put the above mentioned plate back to its place.

IMPORTANT! Before turning on the unit, be sure that the SOUND FREQUENCY switch is in OFF position, and the switch of audible sound is in LOW position.

Installation:

	With the help of the enclosed accessories fix the central unit of the product to the wall or other vertical surface.
	Connect the adapter to the power source. The other end of the adapter has to be in POWER JACK connection of the central unit (see the above written).
	Speakers' position: you can place the four speakers to one side or both sides of a table or paling. Place two speakers higher, two speakers lower. You can turn them out from the central unit or cross them. These ways birds receive continuous sound effects. If you are not sure to where and how place the speakers, we suggest you fixing them temporarily by a wire, and you can fix them constantly even after you have decided which is the right place. When you place them on a tower, glass roof or roof, please follow these instructions: place some higher, some lower and turn them into opposite position.
	Set the unit according to the repelled birds (See detailed steps at Programming!)
	Be sure the sound volume is in LOW position (turn the swich anti-clockwise)
	Set SOUND FREQUENCY switch to HIGH position. The unit will start to operate immediately.
	Set the sound volume into the desired position.
	Close the top of the central unit.

Programming:
For programming Broadband Pro bird repeller you will need a small screw-driver, a toothpick or any small, rigid item to set the switches. You can found the switches necessary for setting at the left hand top of the central unit. The switch is ON if you slide it to the right and it is OFF if you slide it to the left.
 

Adjusting emitted sound:
For adjusting the emitted sound you have to use the first to eight switches of the board.
All sounds have a number you can see on the right side of the board:

	Sound 1 (starling/pigeon I. )
	Sound 2 ( gull/pigeon II.)
	Sound 3 ( peregrine falcon)
	Sound 4 (sharp-shinned hawk)
	Sound 5 (cooper's hawk)
	Harrassment I.
	Harrassment II.
	Harrassment III.

Settings:
You can set here the time intervals of emitting for example warning sounds (only daytime, only night or 24 hours a day) in random or normal mode of operation.

There are two switches for delayed setting (nr.1. and 2.). If you operate the unit with these switches, you can adjust the period for emitting bird sounds (how many seconds or minutes later). SHORT mode of operation is only suggested to use during testing, because in this mode success is not guaranteed for a longer period. Time periods when unit emits sounds are depend on the settings of DELAY and RANDOM switches. If you select RANDOM mode, the bird repeller will operate between a minimum and a maximum period. In other case, it will operate in the minimum period.

Adjusting operating periods:
There are two "time switches" on the unit, switch number 3 and 4. If you select night operation, it bird repeller will operate only at night, and if you select day operation, Broadband Pro will operate only daytime. In the unit there is a photocell, which senses sunlight. If you select 24 hours operation, the unit will continuously operate day and night.

Random setting:
By setting RANDOM you can select emitting required bird sounds to be random or not. This mode of operation is so important, because when the unit emits random sounds, birds (pigeon, swallow, sparrow, starling etc.) are not able to accommodate to it. You have to choose switch number 5. for this operation.

Setting ultrasound:
The unit emits ultrasound continuously, not depending on setting modes. You can set the frequency of ultrasound to HIGH, MED and LOW positions. We suggest starting with LOW position, then change to other ones later.

Setting volume:
There is an AUDIO VOLUME switch on the central unit, with which you can set the volume of audible sound. By turning it to LOW, volume will be lower and by turning it to HIGH, volume will be higher.

Warranty:
We grant you 1 year guarantee from the purchasing date. It means we exchange the product.

Warranty is not valid in the following cases:
aggresive intervention, breaking, unsuitable using, carelessness, injuring, changing or unsuitable using.
The bad product should be sent back to the distributor's address (Harp's Ltd., H-5000 Szolnok, József Attila út 38. I/8.) with the guarantee bond and the copy of the invoice. The buyer has to contact the distributor before sending back the product. If any of these conditions miss, the guarantee is not valid. It is the buyer who pays the cost of sending back the product, and it is the distributor who pays the cost of sending a new unit.

< back to homepage